Focusrite Pro RedNet D16R MkII

Home Focusrite Focusrite Pro RedNet D16R MkII
RedNet D16R MkII is a 16x16 digital interface for Dante networks, with channel level control for individual inputs and outputs.
Email A Friend Add To Wishlist
FRT-REDNETD16RMKII
Focusrite
Mac & Win
Usually ships in 1-2 business days.
Availability: In stock
As low as $1,889.99

RedNet D16R MkII is a 16-channel bi-directional digital interface for Dante networks. The 1Urackmount device features individual input and output channel level controls, allowing for precise calibration and control of all input and output levels using RedNet Control. RedNet D16R MkII features power supply and Ethernet redundancy with auto switchover in case of failure.


Various connection options make RedNet D16R MkII a flexible addition to any Audio-over-IP system. A pair of DB25 multipin connectors each connect eight channels of AES3 I/O into and out of the interface, while XLR and RCA ports enable two-channel AES3 and S/PDIF connections, respectively, to be made. Sample rate conversion on every input enables external equipment to operate at different sample rates, and DARS signals are accepted on the XLR connector. WordClock I/O on BNC connectors allows synchronization to house clock, or syncing external equipment to the Dante network.

INPUT / OUTPUT TRIM

Input Trim

 

-78 to 0dB in 1dB steps (per channel)

 

Output Trim

 

-78 to 0dB in 1dB steps (per channel)

 

INPUT SAMPLE RATE CONVERTORS

Sample Rate Range

 

32Hz to 214kHz

 

Gain Error

 

-0.3dB

 

Dynamic Range

 

Greater than 138dB (-60 dBFS method)

 

THD + N

 

Less than -130dB (0.00003%); 0 dBFS input

 

Latency

 

11 to 45 samples (network and input sample rate dependent)

 

DIGITAL PERFORMANCE

Supported Sample Rates

 

44.1 / 48 / 88.2 / 96 / 176.4 / 192 kHz (-4% / -0.1% / +0.1% / +4.167%)at 24 bit

 

Clock Sources

 

Internal, Word Clock, DARS, AES input 1-2, AES input 9-10 or from DanteNetwork Master

 

External Word Clock Range

 

Nominal sample rate 7.5%

 

REAR PANEL CONNECTIVITY

AES/ EBU

Channel Count

 

2 x 2 S/PDIF Channels (reduces AES/EBU input channels)

 

Input And Output

 

2 x DB25 connectors (AES59 Combined I/O / Tascam Digital)

 

Alternate Input (Optional DARS)

 

1 x Female XLR (replaces DB25 channels 1-2)

 

Alternate Output

 

1 x Male XLR (duplicates DB25 channels 1-2)

 

S/PDIF

Channel Count

 

2 x 2 S/PDIF Channels (reduces AES/EBU input channels)

 

Input

 

1 x RCA phono socket (replaces DB25 channels 3-4)

 

Output

 

1 x RCA phono socket (switchable, duplicates any DB25 channel pair)

 

WORD CLOCK

Input

 

1 x BNC 75 port (switchable termination)

 

Output

 

1 x BNC 75 port

 

PSU & NETWORK CONNECTIONS

PSU

 

2 x Internal, 100-240V, 50/60Hz, consumption 30VA

 

Network

 

2 x EtherCON NE8FBH-S, also compatible with standard RJ45 connectors(Accomodates rugged EtherCON NE8MC*. Does not intermate with Cat 6 cableconnector NE8MC6-MO and NKE65* cable)

 

FRONT PANEL INDICATORS

Primary PSU (A)

 

Green LED. Illuminates when an AC input is applied and all DC outputsare present

 

Secondary PSU (B)

 

Green LED. Illuminates when an AC input is applied and all DC outputsare present

 

Secondary Network

 

Green LED. Indicates that a network connection is present on secondaryport when in redundant mode. Not used in switched mode

 

Network Locked

 

Green LED. When unit is following network grand master, shows validnetwork lock. When unit is network master, shows lock to indicated clocksource. Flashing indicates external clock is selected but not connected

 

Sample Rate

 

Orange LED for each: 44.1kHz, 48kHz, x2, x4

 

Pull Up/Down

 

Orange LED. Indicates unit is set to operate on a Dante pull up/downdomain

 

Signal Indicators

 

16 Green LEDs, 8 input/8 output indicators. Illuminate @ -126dBFS

 

Clock Source

 

Orange LED for each: Internal, Word Clock, DARS, Input 12 and Input910

 

Primary Network

 

Green LED. Indicates that a network connection is present on primaryport when in redundant mode. When in switched mode, a valid network connectionat either primary or secondary network port will cause this LED to illuminate

 

NETWORK MODES

Redundant

 

Allows unit to connect to two independent networks

 

Switched

 

Connects both ports to integrated network switch allowingdaisy-chaining of devices

 

DIMENSIONS

Height

 

44.5mm/ 1.75"

 

Width

 

482.6mm/ 19"

 

Depth

 

263mm/ 10.35"

 

WEIGHT

Weight

 

3.84kg

 

POWER

PSU

 

2 x Internal, 100-240V, 50/60Hz, consumption 30VA.

 

HEAT PERFORMANCE

Operating Temperature

 

Operates at up to an ambient temperature of 50 degrees Celcius

Write Your Own Review
You're reviewing:Focusrite Pro RedNet D16R MkII
Your Rating

Related Products